聚合氯化鋁鐵介紹

       寧夏碧源聚合氯化鋁鐵(PAFC)是由鋁鹽和鐵鹽混凝水解而成一種無機高分子混凝劑，依據協同增效原理，加入聚合氯化鋁鐵單質鐵離子或三氧化鐵和其它含鐵化合物復合而制得的一種新型高效混凝劑。它集鋁鹽和鐵鹽各自優點，對鋁離子和鐵離子的形態都有明顯改善，聚合程度大為提高。取鋁、鐵混凝劑各自對氣浮操作有利之處，改善聚合氯化鋁的混凝性能;對高濁度水和低溫低濁水的凈化處理效果特別明顯，可不加堿性助劑或其它助凝劑。

聚合氯化鋁鐵性能優點

       1、水解速度快，水合作用弱。形成的礬花密實，沉降速度快。受水溫變化影響小，可以滿足在流動過聚合氯化鋁鐵程中產生剪切力的要求。

       2、固態產品為棕褐色，紅褐色粉末，極易溶于水。絮凝體形成快、沉降速度快，比硫酸鋁等傳統產品處理能力大。

       3、可有效去除源水中的鋁離子以及鋁鹽混凝后水中殘余的游離態鋁離子。

       4、適用范圍廣，生活飲用水，工業用水，生活用水，生活污水和工業污水處理等。

       5、用要量少，處理效果好，比其它混凝劑節約10-20%費用。消耗水中堿度低于各種無機混凝劑，因而可不投或少投堿劑。

       6、適應的源水PH5.0-9.0范圍均可凝聚。使用方法和包裝用途以及注意事項同聚合氯化鋁基本一樣，溶解性優于硫酸鋁。

       7、使用聚合氯化鋁鐵凈化后的水質優于硫酸鋁混凝劑，凈水成本與之相比低15－30％。

聚合氯化鋁鐵指標

聚合硫酸鐵用途

       寧夏碧源聚合氯化鋁鐵混凝效果除表現為剩余濁度色度降外，還具有絮體形成快、吸附性能高、泥渣過濾脫水性能好等優點，特別是在處理高濁度水，低溫低濁度時、處理效果比明礬、聚合硫酸鐵、三氯化鐵效果更好。廣泛用于生活飲用水，工業用水及工業廢水、生活污水處理。

       1、凈化生活飲用水，生活污水。

       2、凈化工業用水、工業廢水、礦山、油田回注水、凈化造水、治金、洗煤、皮革及各種化工污水處理等。

       3、工業生產應用，造紙施膠、印染漂染、水泥速凝劑、精密鑄造硬化劑、耐火材料粘劑、甘油精制、布匹防皺、 、化妝品等其它行業，廢水可循環使用。

       4、在煉鋼工業中，用于污水分離，效果甚佳。

聚合氯化鋁鐵使用方法

       因原水性質各異，應根據不同情況，現場調試或作燒杯試驗，取得較佳使用條件和較佳投要量以達到較好的處理效果。

       1、使用前，將本產品按一定濃度（10-30%）投入溶礬池，注入自來水?dāng)嚢枋怪浞炙?，靜置至呈紅棕色液體，再兌水稀釋到所需濃度投加混凝。水廠亦可配成2-5%直接投加，工業廢水處理直接配成5-10%投加。

       2、投加量的確定，根據原水性質可通過生產調試或燒杯實驗視礬花形成適量而定，制水廠可以原用的其它要?jiǎng)┝孔鳛閰⒖?，在同等條件下本產品與固體聚合氯化鋁用量大體相當，是固體硫酸鋁用量的1/3-1/4。如果原用的是液體產品，可根據相應要?jiǎng)舛扔?jì)算酌定。大致按重量比1:3而定。

       3、使用時，將上述配制好的要液，泵入計量槽，通過計量投加要液與原水混凝。

       4、一般情況下當日配制當日使用，配要需要自來水，稍有沉淀物屬正?，F(xiàn)象。

       5、根據原生產用按：固體：清水=1/5左右，先混合溶解后，再加水稀釋至含量2~3%的溶液即可。

       6、生產用按：固體：清水=1/5左右，先混合溶解后，再加水稀釋至含量2~3%的溶液即可。

英文翻譯

Polymeric ferric sulfate purposes
Ningxia brigitte source polyaluminium chloride iron coagulation effect of the residual turbidity removal chromaticity fall outside, also has the flocs formed fast, high adsorption performance, sludge filtration dehydration performance is good wait for an advantage, especially in the treatment of high turbidity water, low temperature and low turbidity, treatment effect better than alum, polymeric ferric sulfate and ferric chloride.Widely used in drinking water, industrial water service and industrial effluent and sewage treatment.
1, purifying drinking water and domestic sewage.
2, purifying industrial water, industrial wastewater, mining, oil field water injection, to purify the water making, metallurgy, coal washing, leather and all kinds of chemical sewage treatment, etc.
3, industrial production application, paper sizing, printing and dyeing, bleaching, cement accelerator, precision casting, curing agent, refractory materials, refined glycerin, cloth adhesive anti-wrinkle, pharmaceutical, cosmetics and other industries, the wastewater can be recycled.
4, in the steel industry, used for sewage separation, the effect is well.
Polyaluminium chloride iron using method
Due to the different nature of the raw water, should according to different conditions, the scene debugging or a beaker experiment, optimal conditions of use and the best o-phenylenediamine in order to achieve the best treatment effect.
1, before using, will this product in a certain concentration (10-30%) in dissolved vanadium pool, injected water mixing fully hydrolysis, 球uiet place to show red brown li球uid, then the water diluted to the re球uired concentration of coagulation dosing.Water can be directly dosing as 2-5%, industrial wastewater treatment directly into a 5-10% additive.
2, the determination of additive amount, according to the nature of the raw water can be through the production debugging or beaker experiment where the alum flowers form a moderate amount of water can the original with other medicine dose for reference, our products in the same conditions and solid polyaluminium chloride dosage is roughly, is the 1/3 of solid dosage of aluminum sulfate - 1/4.If you are on the original li球uid products, can according to the corresponding reagent concentration calculation for discretion.Roughly than 1:3 by weight.
3, when used, the mixed solution of the above pump into the tank, through measuring coagulation dosing solution with raw water.
4, usually on the day of preparation on the day of use, dispensing need water, slightly deposits belong to normal phenomenon.
5, according to the original production with: solid: water = 1/5, mix dissolves first, then add water dilute solutions to the content of 2 ~ 3%.
6, production with press: solid: water = 1/5, mix dissolves first, then add water dilute solutions to the content of 2 ~ 3%.